Arrow VM1012-B Especificaciones descargar pdf (Pagina 33)

sliding the new camshaft bearing shell over proper

adapter.

(2) Position the rear bearing in the tool. Install

horseshoe lock and by reversing removal procedure,

carefully drive bearing shell into place.

(3) Install the remaining bearings in the same

manner. The Bearings must be carefully aligned

to bring oil holes into full register with oil pas-

sages from the main bearing. If the camshaft

bearing shell oil holes are not in exact align-

ment, remove and install them correctly.

(4) Install a new rear plate o-ring at the rear of

camshaft. Be sure this seal does not leak.

OIL PAN

REMOVAL

(1) Disconnect the negative battery cable.

(2) Raise the vehicle on hoist.

(3) Drain the oil.

(4) Remove the oil pan lower cover (Fig. 45).

(5) Remove the bolts from oil pan. Remove the 6

bolts that are on the inside of the oil pan.

(6) Remove the oil pan.

INSTALLATION

(1) Remove all gasket material from cylinder block.

Be careful not gouge or scratch aluminum pan seal-

ing surface.

(2) Apply a continuous 3 mm bead of Silicone

Sealer to oil pan, install within 10 minutes. Install

the oil pan.

(3) Install the inside oil pan bolts. Torque bolts to

11 N·m (8 ft. lbs.).

(4) Torque the smaller oil pan bolts to 11 N·m (8 ft.

lbs.). Torque the larger oil pan bolts to 25 N·m (18 ft.

lbs.).

(5) Install the oil drain plug. Torque to 79 N·m (58

ft. lbs).

(6) Lower the vehicle from hoist.

(7) Fill engine with proper amount of oil.

(8) Connect the negative battery cable.

OIL PUMP

REMOVAL

(1) Disconnect the negative battery cable.

(2) Remove the timing gear cover. Refer to timing

gear cover removal and installation in this section).

(3) Remove the oil pump (Fig. 46).

INSTALLATION

(1) Install new O-ring and lubricate with clean

engine oil.

(2) Install the oil pump. Torque screws to 27.5 N·m

(20 ft. lbs.). Check for normal backlash between

pump and crankshaft gears.

(3) Install the timing gear cover. Refer to timing

gear cover removal and installation in this section.

INTERNAL VACUUM PUMP

REMOVAL

(1) Disconnect the negative battery cable.

Fig. 45 Oil Pan

1 – LOWER OIL PAN COVER

2 – OIL DRAIN PLUG

Fig. 46 Oil Pump Removal

1 – CAMSHAFT GEAR

2 – CRANKSHAFT GEAR

3 – OIL PUMP

4 – VACUUM PUMP

XJ ENGINE 9 - 33

REMOVAL AND INSTALLATION (Continued)

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 51 52

Comentarios a estos manuales

Sin comentarios

Delock 41820 Datový list (1 strany)

Značka: Delock | Kategorie: Cable interface/gender adapters | Velikost: 0.33 MB |

Tabulka s obsahem

USB pin header female

Další produkty a příručky pro Adaptéry kabelového rozhraní / pohlaví DeLOCK

Modely	Typ Dokumentu
65012	Datový list DeLOCK USB A Adapter, 1 stránky
84311	Datový list DeLOCK 2.5 IDE/2.5 IDE, 1 stránky
61767	Datový list DeLOCK 61767, 1 stránky
61768	Datový list DeLOCK 61768, 1 stránky
65244	Datový list DeLOCK 65244, 1 stránky
65270	Datový list DeLOCK 65270, 1 stránky
65250	Datový list DeLOCK 65250, 1 stránky
65240	Datový list DeLOCK Displayport/mini Displayport, 1 stránky
41825	Datový list DeLOCK 1 x 9-pin 2.54 mm/2 x USB 2.0-A, 1 stránky
65258	Datový list DeLOCK 65258, 1 stránky
65219	Datový list DeLOCK USB 3.0 Adapter, 1 stránky
65289	Datový list DeLOCK 65289, 1 stránky
65256	Datový list DeLOCK 65256, 1 stránky
65243	Datový list DeLOCK 65243, 1 stránky
88411	Datový list DeLOCK 88411, 1 stránky
61847	Datový list DeLOCK 61847, 1 stránky
84400	Datový list DeLOCK 84400, 1 stránky
41824	Datový list DeLOCK 9-pin 2.54 mm/2 x USB 2.0, 1 stránky
84419	Datový list DeLOCK 3.5 mm - Toslink, 1 stránky
65010	Datový list DeLOCK 65010, 1 stránky

Arrow VM1012-B Especificaciones Pagina 33

Comentarios a estos manuales

DeLOCK 41820 manuály

Delock 41820 Datový list (1 strany)

Tabulka s obsahem

Další produkty a příručky pro Adaptéry kabelového rozhraní / pohlaví DeLOCK